| |
Technical Terminology

Technical Terminology

(1.) Quartz crystal is a Piezo-Electric Device
Quart is kind of crystallized Silicon Dioxide (SiO2). The quartz crystal structure has the characteristics of piezoelectric effect( Fig 1), to exert pressure in the crystal in certain directions; the direction of the vertical force will produce electrical potential. Energy is converted between electrical and mechanical, millions of times per second. Hence, its characteristic is very different from other components.

According to different cutting orientation with quartz bars, there are different kinds of quartz plates such as AT, BT, CT….. –cut plates, which will determine the characteristic of quartz crystal device. Cutting orientation process determines:

1) The vibration mode; 2) frequency range; 3) characteristics of the operating temperature

Quartz Crystal unit’s characteristics depend on the cutting orientation( Fig 2):

a) Tuning Fork : KHz Frequency level, such as 32.768KHz:
b) AT-Cut type: MHz frequency range, such as 12MHz, 26MHz, 125MHz
c) SAW type:frequency range from MHz to GHz
(Fig.1) Typical Structure of HC-49U and SMD Quartz Crystal (Fig.2) Cutting Orientation of Quartz Crystal
(Fig.3) HC-49U Crystal (Fig.4) SMD-Crystal
(2.) Equivalent Model of a Quart Crystal
(3.) Raw Parameters of Crystal

Rs, C0, C1 and L1 give you all the information concerning impedance change of a crystal near by it operating frequency
Temperature Characteristic AT Cut
For AT Cut, usually +/- 30 to 50 ppm over -10 to +60
Always refer to 25 degree C as 0 ppm
Temperature Characteristic Tuning Fork
For Tuning Fork usually over 200 ppm
Common habit is to refer to 25 degree C as 0 ppm
Consider seriously to allow +80ppm typical for 25 C
(4.) AT cut & Tuning Fork Characteristic
Tuning Fork AT-cut
Frequency kHz MHz
Standard consumption 02.uW 50uW
ESR Large Less than TF
Temperature characteristic Large tolerance Deviation than AT -cut
(5.) Overtone or Fundamental of Crystal
Fundamental Overtone
Frequency (AT Cut) 4MHz to 50MHz (Depend on application) 18MHz to over 100MHz
ESR Lower ESR Higher ESR
Drop Shock Performance The higher the frequency, the worst the drop shock Better due to much thicker blanks
Pullability Can be designed for FM, PLL, VCO applications Very High Q, hence frequency less dependent on other component variations.
Circuit Design Usually does not require filter to precent crystal oscillating at its overtones Usually requires filters to prevent crystal oscillating at its fundamental frequency

Note:
– Above information is reference only. If there any question, Pls contact us for enquiry.
– We will reserves the right to change above information for improvement without notification.

一分时时彩 一分时时彩 分分时时彩走势图-欢迎您 一分时时彩-欢迎您 三分快三-官网 三分快三计划-欢迎您 三分快三-欢迎您 三分快三--Welcome 腾讯分分开奖计划-欢迎您 三分快三-欢迎您 三分快三平台-欢迎您 三分快三计划-欢迎您 三分快三计划 三分快三-官网 腾讯分分彩官网-欢迎您 三分快三计划 网易彩票app-欢迎您 亚洲彩票-官网 爱乐透彩票---一分时时彩_欢迎您 亚洲彩票--Welcome 网易彩票网---一分时时彩_欢迎您 网易彩票app 亚洲彩票-欢迎您 极速时时彩平台 网易彩票app 网易彩票app--Welcome 网易彩票app 网易彩票app-官网 网易彩票网 时时彩官网 幸运时时彩 时时彩官网--Welcome 时时彩官网--Welcome 时时彩官网--Welcome 极速时时彩平台--Welcome